Munter hitch/cs: Difference between revisions

Line 1:

{{Infobox uzel

Line 6:

Line 7:

| použití = Jištění, záchranné techniky

}}

</div>

Poloviční lodní smyčka je jedním ze základních uzlů. Je využívána pro jištění bez jistící pomůcky (např. ATC) pouze za pomocí lana a HMS karabiny. Je taktéž využívána v pokročilých lanových technikách (např. při záchranných pracech).

== Vázání ==

Viz ilustrované postupy níže

</div>

== Tying ==

</div>

=== Tying for an anchor belay (easy method) ===

This method is very robust and suitable for learning how to tie the hitch.

</div>

[[File: Hms_ez_step1.png|140px]]

[[File: Hms_ez_step2.png|140px]]

[[File: Hms_ez_step3.png|140px]]

[[File: Hms_ez_step4.png|140px]]

[[File: Hms_ez_step5.png|140px]]

[[File: Hms_ez_step6.png|140px]]

</div>

'''Steps description''': start with making a loop on a rope (1) and pull the loop on your thumb (2). Then place another strand over your thumb (3) and close the hand with your index finger. Next, pull the carabiner exactly through the rope in the path of your thumb (4). Screw the safety-lock (5), inspect that everything is correct (6) and pull the break-strand (7) to test if the munter hitch flips into another munter as a final check.

</div>

=== Tying for a harness belay ===

[[File: Hms_harness_step0.png|120px]]

[[File: Hms_harness_step1.png|120px]]

[[File: Hms_harness_step2.png|120px]]

[[File: Hms_harness_step3.png|120px]]

[[File: Hms_harness_step4.png|120px]]

[[File: Hms_harness_step5.png|120px]]

</div>

'''Steps description''': start with a rope through the carabiner which is attached to your harness. Take a bite of a rope (1) and create a loop (2). Then you open the carabiner gate (3) and seat the loop into the carabiner (4). Screw the safety-lock (5), inspect that everything is correct (6) and pull the break-strand (7) to test if the munter hitch flips into another munter as a final check.

</div>

== Belaying ==

Always hold the break strand! Belaying with Munter hitch is reliable and reasonably comfortable. Munter works smoothly when not loaded, yet giving friction to catch a fall once tensioned. It blocks regardless of the angle of the breaking hand. The main reason why it is used less often is that if the rope is pulled through the hitch under tension, Munter tends to tangle the rope.

</div>

[[File: Hms_harness_step0.png|120px]]

[[File: Hms belay with climber.png|120px]]

[[File: Munter_fingers_safe.png|144px]]

</div>

=== Belaying risks ===

When belaying with Munter hitch, aside from always holding the break strand, belayer should pay attention to keep fingers at a respectful distance from the knot, otherwise he might risk jamming his fingers into the belay, which might result in a severe finger injury. Belayer should also ensure to tie the Munter in a way that it does not interfere with the carabiner gate/lock. Otherwise the rope friction might unlock, and maybe even open the gate of the carabiner.

</div>

[[File: Munter_fingers.png|144px]]

[[File: hms_belay_left_top.png|120px]]

[[File: hms_belay_left_bot.png|120px]]

</div>

== Tie-off - Mule overhand ==

This is the most recognized method to tie-off the mule overhand to set your hands free. The tie-off consists from a slipknot and then overhand knot, both of which are tied around the life end of the rope. As both of these knots are tied with a bite and rope is also pulled through the carabiner, it takes practice to be able to securely inspect the tie-off.

</div>

[[File: hms_tieoff_step1_p6w.png|120px]]

[[File: hms_tieoff_step2_p8w.png|160px]]

[[File: hms_tieoff_step3_p8w.png|160px]]

[[File: hms_tieoff_step4_p8w.png|160px]]

[[File: Munter_tieoff_step5.png|200px]]

[[File: hms_tieoff_step7_p8w.png|160px]]

[[File: hms_tieoff_step8_p8w.png|160px]]

[[File: hms_tieoff_step9_p6w.png|120px]]

[[File: hms_tieoff_step10_p6w.png|120px]]

</div>

'''Steps description''': If the knot is not in the correct position, give a bit of a slack first to flip the knot (1). Next create a loop (2) and move it behind the life end (3). Pull a bite of the belay end through the loop (4) effectively making a slipknot around the life end of the rope. Now grab the bite with a hand (5) and simultaneously take out slack out of the system while releasing the other hand (6), note that the break strand is always hold during this step. Pull the bite through the carabiner (7), increase is size if necessary for the next steps. Secure the tie-off by making an overhand around the life end of the rope (8,9).

</div>

= In-depth section =

</div>

== More tying methods ==

For tying, see the methods below.

</div>

=== Metoda jednou rukou ===

@@ Line 1: / Line 1: @@
+<div class="mw-translate-fuzzy">
 <languages/>
 {{Infobox uzel
@@ Line 6: / Line 7: @@
 | použití = Jištění, záchranné techniky
 }}
+</div>
 Poloviční lodní smyčka je jedním ze základních uzlů. Je využívána pro jištění bez jistící pomůcky (např. ATC) pouze za pomocí lana a HMS karabiny. Je taktéž využívána v pokročilých lanových technikách (např. při záchranných pracech).
+<span id="Quick_overview"></span>
+<div class="mw-translate-fuzzy">
 == Vázání ==
 Viz ilustrované postupy níže
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+== Tying ==
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+=== Tying for an anchor belay (easy method) ===
+This method is very robust and suitable for learning how to tie the hitch.
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+[[File: Hms_ez_step1.png|140px]]
+[[File: Hms_ez_step2.png|140px]]
+[[File: Hms_ez_step3.png|140px]]
+[[File: Hms_ez_step4.png|140px]]
+[[File: Hms_ez_step5.png|140px]]
+[[File: Hms_ez_step6.png|140px]]
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+'''Steps description''': start with making a loop on a rope (1) and pull the loop on your thumb (2). Then place another strand over your thumb (3) and close the hand with your index finger. Next, pull the carabiner exactly through the rope in the path of your thumb (4). Screw the safety-lock (5), inspect that everything is correct (6) and pull the break-strand (7) to test if the munter hitch flips into another munter as a final check.
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+=== Tying for a harness belay ===
+[[File: Hms_harness_step0.png|120px]]
+[[File: Hms_harness_step1.png|120px]]
+[[File: Hms_harness_step2.png|120px]]
+[[File: Hms_harness_step3.png|120px]]
+[[File: Hms_harness_step4.png|120px]]
+[[File: Hms_harness_step5.png|120px]]
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+'''Steps description''': start with a rope through the carabiner which is attached to your harness. Take a bite of a rope (1) and create a loop (2). Then you open the carabiner gate (3) and seat the loop into the carabiner (4). Screw the safety-lock (5), inspect that everything is correct (6) and pull the break-strand (7) to test if the munter hitch flips into another munter as a final check.
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+== Belaying ==
+Always hold the break strand! Belaying with Munter hitch is reliable and reasonably comfortable. Munter works smoothly when not loaded, yet giving friction to catch a fall once tensioned. It blocks regardless of the angle of the breaking hand. The main reason why it is used less often is that if the rope is pulled through the hitch under tension, Munter tends to tangle the rope.
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+[[File: Hms_harness_step0.png|120px]]
+[[File: Hms belay with climber.png|120px]]
+[[File: Munter_fingers_safe.png|144px]]
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+=== Belaying risks ===
+When belaying with Munter hitch, aside from always holding the break strand, belayer should pay attention to keep fingers at a respectful distance from the knot, otherwise he might risk jamming his fingers into the belay, which might result in a severe finger injury. Belayer should also ensure to tie the Munter in a way that it does not interfere with the carabiner gate/lock. Otherwise the rope friction might unlock, and maybe even open the gate of the carabiner.
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+[[File: Munter_fingers.png|144px]]
+[[File: hms_belay_left_top.png|120px]]
+[[File: hms_belay_left_bot.png|120px]]
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+== Tie-off - Mule overhand ==
+This is the most recognized method to tie-off the mule overhand to set your hands free. The tie-off consists from a slipknot and then overhand knot, both of which are tied around the life end of the rope. As both of these knots are tied with a bite and rope is also pulled through the carabiner, it takes practice to be able to securely inspect the tie-off.
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+[[File: hms_tieoff_step1_p6w.png|120px]]
+[[File: hms_tieoff_step2_p8w.png|160px]]
+[[File: hms_tieoff_step3_p8w.png|160px]]
+[[File: hms_tieoff_step4_p8w.png|160px]]
+[[File: Munter_tieoff_step5.png|200px]]
+[[File: hms_tieoff_step7_p8w.png|160px]]
+[[File: hms_tieoff_step8_p8w.png|160px]]
+[[File: hms_tieoff_step9_p6w.png|120px]]
+[[File: hms_tieoff_step10_p6w.png|120px]]
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+'''Steps description''': If the knot is not in the correct position, give a bit of a slack first to flip the knot (1). Next create a loop (2) and move it behind the life end (3). Pull a bite of the belay end through the loop (4) effectively making a slipknot around the life end of the rope. Now grab the bite with a hand (5) and simultaneously take out slack out of the system while releasing the other hand (6), note that the break strand is always hold during this step. Pull the bite through the carabiner (7), increase is size if necessary for the next steps. Secure the tie-off by making an overhand around the life end of the rope (8,9).
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+= In-depth section =
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+== More tying methods ==
+For tying, see the methods below.
+</div>
 === Metoda jednou rukou ===