Tuber (Tubular belay device)

Tuber
Other names	Tubular belay device, ATC, Reverso, Guide
Use(s)	Belay, abseiling, rescue techniques, ascending (atypical)
Pros	Well-tested and optimized, super-easy to give slack, useful for belaying of the second climber (guide mode), lightweight, can be used with double/twin ropes, multi-purpose
Cons	Does not provide assisted braking function, it blocks only if dead rope is in the opposite direction to the live rope, can bite into skin of the brake hand index finger if used inappropriately, in majority of the devices the setup for lowering of a second climber is cumbersome

Tubular belay devices are the most commonly used belay devices during training of advanced climbing and rescue techniques, multipitching and management of twin/double ropes. In some countries/clubs, they have been replaced by assisted tubular belay devices for single-pitch training. They are prohibited in some gyms due to alleged security concerns (for details, see the security concerns section).

Belaying from the harness

Slack taking

• 

  Start in the resting position

• 

  Feed the slack through the device by simultaneously moving both hands

• 

  Move the belay hand back into a fully blocking position

• 

  Tunnel up the rope by the belay hand to the resting position

• 

  Final resting state, repeat the steps if you need to take more slack

Slack feeding

• 

  Tunnel down

• 

  Feed the slack through the device by simultaneously moving both hands

• 

  Put the belay hand back into the safe resting position

• 

  Final resting state, repeat the steps if you need to give more slack

General risks

Always hold/control the break strand at least with one hand and keep the break strand downwards unless giving or taking the slack. Keep your hand at least a few centimeters from the belay device to avoid pinching of the skin. Do not lift your hand too high (above the device) while giving the slack. One of the commonly seen bad habit is keeping the hand raised for a prolonged time during belaying.

• 

  Always hold the break strand downwards unless feeding/taking the rope

• 

  Feed or take the rope from the front of the device

• 

  Not holding the break strand can result in fatal injuries

• 

  Holding the break hand too close to the tuber leads to a risk of pinching the skin of the break hand index finger.

• 

  Do not lift the break hand unnecessary high during the break strand manipulation.

• 

  Do not leave the hand in the upper position if not taking or giving the slack.

Belaying at the anchor

Belaying the second climber

• 

  Setup for belaying second climber with a guide-mode tuber

• 

  Taking slack is done by simultaneously moving both hands

• 

  Alternatively, the same technique which is described below for belaying the lead climber can also be used for belaying the second climber with a tuber without a guide mode.

Belaying the lead climber

• 

  While belaying from the anchor, redirect the rope in a way that it points upwards even in a case of a fall. Usually an unlocked D-shaped carabiner is used.

• 

  This redirection can be also in some cases built by a quickdraw placed in the second bolt of the anchor if the carabiner is short and the bolt is placed high enough.

• 

  Once the lead climber makes two secure running protections on the route, the redirection is removed.

Belaying from harness at the anchor

• 

  Redirection of the sharp end of the rope for belaying from harness at the anchor

During belay from harness at the anchor point redirects the rope through the anchor till the first two pieces of the running protection are placed.

Anchor-belay risks

Belaying at the anchor brings additional risks on top of the general risks. Unlike during belay at a ground level, during anchor belay, climber can get below the tuber level during a fall. If the climber would fall before the first running protection is placed, the tuber would not block as both the break strand and the live strand would be pointed the same direction as illustrated below.

• 

  While belaying from the anchor, redirect the rope in a way that it points upwards even in a case of a fall.

• 

  If the rope is not redirected properly, tuber rotates into a non-breaking position during a fall, which easily results into a ground fall.

Abseiling

TODO (redirect to technique page)

Tuber as an ascender

Using tuber as an ascender

Due to its self-arresting nature, tubular belay devices can be used in a guide mode as an ascender, effectively replacing for example garda hitch in self-rescue from crevasses.

Security concerns

Disclaimer: This section reflects both subjective opinions and the positions of various alpine clubs. Qualified readers are encouraged to form their own judgment, or to follow the recommendations of recognized organizations. Unqualified readers are pointed to their club rules/recommendations. The aim here is not to prescribe one device over another, but to present different perspectives, so that climbers can make their own informed and responsible decisions. Neither Karl, nor any other contributor to this article promotes or discourages the use of specific devices; the responsibility lies fully with the climber and belayer.

With non-assisted belay devices, the brake hand is the single point of failure. If the rope is released, a fall will not be slowed-down. While this carries inherent risk (if you let go, you let go), many climbers value these devices because they provide clear, immediate feedback on correct technique which helps to reinforce good habits. Also feeding the slack is except few cases smoother than with assisted-breaking devices.

Assisted belay devices, on the other hand, offer an additional layer of security, as the device itself can often stop a fall even if the break hand fails. This can reduce the likelihood of accidents. At the same time, the added security may also allow incorrect handling to go unnoticed and, over time, weaken safe habits as seen even among experienced users.

Studies by the German Alpine Club (DAV) in 2016 once again indicated more reported accidents with non-assisted tubular devices than with assisted devices, though most accidents were still traced back to incorrect use (burned hands). Following these findings, gyms and clubs in Germany and the Netherlands began to strongly recommend assisted belay devices, or even banned the non-assisted ones. Yet, for instance a study conducted in 2019 year showed that Megajul is statistically more dangerous than a tubular device. This was obviously caused by a very small sample size of accidents. However, this might illustrate that user experience and handling technique may matter more than the device type. Affordability may also play a role, as non-assisted devices might have been chosen by newcomers as a starter option. As newcomers are less experienced, it is therefore reasonable to expect that they have a higher accident risk. Also in the same study, it has been shown that during bouldering there is approximately 10 times higher chance of an accident needing an ambulance when compared to a climbing hall, showing climbing is a generally safer option.

Different alpine clubs highlight different aspects. For instance the education commission of the Czech Alpine Club (ČHS), highlights non-assisted devices for the way they build good habits, yet at the same time recommends assisted devices operated in a same way as the non-assisted ones for youth and newcomers.

There are reported severe accidents both for letting go non-assisted belay device and for reckless handling of an assisted belay device. However, most of the accidents occur not while belaying, but during abseiling.REF For this reason, good technique, clear communication and training at a real conditions (fatigue resistance) remain the most critical safety priorities, regardless of device. Ultimately, the choice of belay device is best made consciously and in agreement between belayer and climber—both of whom carry the most imminent consequences of that choice.